www.ericthecarguy.com This video is an update to the original video that I posted on this job that covers doing this procedure on the car. In the last video I was not able to do this because the lower ball joint was broken and I was also replacing the bearing in addition to the rotor.Stay dirty...


EricTheCarGuyHonda's are infamous for having screws in the brake rotors to hold them in place from the factory. These screws many times are difficult to get out without stripping the screw. I show you a couple different ways to remove them. Also, if your rotor is stuck to your hub, I show you how to get them...


nukem384This was a request from a while ago and I'm happy to get to it now. I did a bunch of video on this car (1990 Honda Accord LX) and have lots more to show you in future episodes. Honda captive rotors are a pain to say the least. For the most part you can take them somewhere that is equipped with an...


Showing you step by step how to do change front brake pads and brake rotors on a 1991 Acura Integra. These basic steps apply to most cars.


ManClub is back with another Monkey Fighting episode. This time our fearless host changes front brake pads and rotors on a 2007 Honda Element. He also covers rotor removal/replacement and lubrication of the sliding pins and other brake components.


These are selected clips from a full length video at www.Teach-Me-Auto.com


teachmeautodotcom2003 Honda CRV Brake Pad and Rotor change part 1 Note: After changing the pads, I pumped the brake numerous times to prime the brakes before they worked.


The only method I use for brake rotor machining is the one authorized by Honda. It is the only method that can assure a good brake job on front wheel drive cars. Few shops other than Honda/Acura shops and Honda/Acura dealers use this method.


Get the Galfer Front Wave GL1800 Performance Rotors here: wingstuff.com/products/24681-front-wave-performance-gl1800-rotors Galfer Performance Front Wave® Honda GL1800 Gold Wing Rotors are made of a proprietary 420 high carbon stainless steel for increased memory retention during heat cycles....


wingstuffcomFor the record - the first gear puller I had picked up off his pile was not the one he had tried to use - the other one was still on the pile where he was working - along with yet another. Hopefully this will help out someone along the way so they dont mess up their case trying to pull a rotor out


dawino6260I think the title covers this one. Honda's are famous for this so I made this little video to help you should you be in this situation. Wear your safety glasses when you do this or whenever you hit things, getting crap in your eye sucks, trust me. Impact drivers can be found at your local tool...


EricTheCarGuyThese are clips from a full length video at www.Teach-Me-Auto.com.


teachmeautodotcomIn this video, I demonstrate how to replace the rear brake pads and rotors in a 2003 Honda CR-V. This car had a seized caliper on the passenger side after I finished shooting this video, so it is now known as the CRV brake job from hell. I am not responsible for any mishaps that may have occurred...


How to Replace and Install brake rotors and new brake pads on 1998 Honda Prelude


take off the caliper to put the new one on


TheTempestFamilyReplacing the pads and rotors on a 2005 Acura TSX. We felt there are a million how to change your brakes videos on youtube, so we decided why not make a quick video, for someone who doesn't want to watch a 20 minutes in depth video on how to change brakes. Quick and Easy. Here you go. The song is...


1) remove the master cylinder cap to release the preassure 2) don't apply emergency brakes if working on rear rotors. 3) when removing rotor use my recommendation in this video to remove them properly without stripping them oк you will need to drill them out..


My 2011 Honda Odyssey EX has had Four (4) front brake Repairs since last February ...and now need a 5th repair! The Rotors have been replaced twice, and those have both been turned. The front brake rotors are now severely warped again as you can see how badly the Steering Wheel shakes as the car...


Dusty57CorvetteMy 2011 Honda Odyssey Ex with Warped Front Brake Rotors, for the 5th time in less than 70000 miles! ( I commute between offices in Cary, Rocky Mount and Wilson, NC... all Highway, everyday). I only bought this car after Honda had promoted the "Newly Engineered Brakes", since my 2007 Odyssey had...


hometechnc2003 Honda CRV Brake Pad and Rotor change part 2 Note: After changing the pads, I pumped the brake numerous times to prime the brakes before they worked.


In this video I show how to remove, and install new brake pads on your 92 93 94 or 95 Honda Civic. It's pretty simple, you remove the front wheels, remove the capliper bolt, lift up the caliper, pull out the pads (if your going to remove the rotor or disc then you must remove the brake...


HondaHowTo1Care to follow? www.twitter.com How to change a distributor cap and rotor on a 1998 Honda Civic. This install is virtually the same for any Honda or Acura that has ignition wires (older models). Music by: incompetech.com


nukem384Shows how a trapped rotor fits together on a 1995 Honda Accord. You'll need a press to replace the brake rotor and wheel bearing on your 5th Generation 1994-1997 Honda Accord. Shows how the hub, wheel bearing and brake rotor fit on the knuckle. Do this repair yourself and save a ton of money....


BradGrisssom
Страница: 1 из 80
